Inline Bowline Knot

fd.jpg

Use: Makes a fixed loop that can be used for a multitude of tiedowns; attaching one rope to another, securing equipment to fixed points, sailing knots. Tension will not move the knot. However it is not often used in mountaineering due to the fact that you can indeed untie the knot with ease.

Step 1: Create a Loop

20180128_190507

Fold the “loose” end of the rope over itself, as to create a loop with the free end remaining on top. Dig the hole.

Step 2: Through the Loop

20180128_190517

Next, create a larger loop by moving the loose end under and up through the previous loop.  The rabbit comes out of the hole.

Note: This larger loop you have just created is what you will use to secure the inline bowline around an object. If you wish to tie it TO something, thread the loose end through the object you wish to secure it to, before bringing it back through the previous loop.

 

Step 3: Around the Running End

20180128_190525

Take the free end, and thread it behind the running end. The Rabbit goes around the Tree

 

Step 4: Weave Back Through The Loop

20180128_190537

Come back over the running end with the free end, and push the free end through the initial loop. The Rabbit goes back into the hole. 

 

Step 5: Pull Tight

fd

Pull it tight to finish off your inline bowline! If done successfully, the knot should not become larger or smaller with tension on the loop (unlike a slipknot).

Too easy! Check out our other knots in our step by step survival knots series.

 

Figure Eight (Flemish) Knot

20171126_174411

Use: Stoppage (similar to an overhand knot), often used in sailing on the mast, the base of the climber’s knot (double figure-8 knot), anchoring, etc.

 

Step 1: Create a “Bight”

20171126_174315Simply fold the rope over itself, leaving a loop, without crossing the rope.

 

Step 2: Over, then Under

20171126_174329Using the free end, weave the end over the long end, and back under to the same side you began, creating a loop.

 

Step 3: Through the Loop

20171126_174337Using the free end again, weave the rope over and down into the loop you created

 

Step 4: Pull and Tighten

20171126_174411

Simply pull both ends of the rope to tighten into a figure eight knot. If you have done each step successfully, your knot should resemble the number 8.

Too easy! Check out our other knots in our step by step survival knots series.

Upside Down Fire

The upside down fire is a self feeding fire that does not require nearly as much stoking and feeding as the traditional teepee campfire. It can burn upwards of 5 hours, uninterrupted, if you do it right. Here are the steps you need to create the upside down fire, along with Dan and I’s own attempt to build it.

Essential Tools:

  • Fire starter (lighter, matches, magnesium stick, etc)
  • Twigs
  • Tinder (Manmade or natural)
  • Knife/ax/saw or some sort of sharp for collecting materials
  • If you are cooking, a vessel or surface to hold your food in

 

20171021_221725

Step 1: Collect your Materials

Once more, we are building this fire using the “twig” method in order to represent a situation in which you may need fire without having store bought materials. Using a small ax and my khukuri knife, we cut down small tree limbs and collected three major types of twigs:

  • Thumb Size
  • Pencil Size
  • Pencil Lead Size

Remember– Try not to pull trees/sticks from the ground. Instead, look for standing deadwood that is dry, easy to break and lacks the moisture than any sticks laying on the ground would.

For tinder, we used a combination of dried grass an a featherstick.

 

20171021_19292820171021_193127

 

Step 2: Build Your Base

Start with the thickest twigs you have, and lay them flat in your pit, one after the other like you are laying down a log pile. Create a layer as large as you want your fire to be. Then use the next thickest, and cross hatch them in a new layer above your first. Continue this pattern until you get to the thinnest twigs, and finally place your tinder bundle on top.

20171021_200310

Step 3: Light The Tinder

For the sake of this attempt, we simply used a lighter, but I would recommend using whatever fire making material or method you have readily available in your EVERY DAY CARRY or at the very least, your backpacking/hiking essentials.

It might take a bit to get the tinder lit long enough that it begins to feed itself, which can be frustrating, but once the twigs light, this fire is capable of burning for hours on end.

Being down by a river on a muggy day, it took upwards of an hour to get our tinder lit long enough. We ended up adding some scraps of napkins we had brought along with us as well. The air was thick with whistles and squeals of the materials as they dried out, but once it got going, we were able to cook over it and enjoy its warmth until bed time.

This method was fairly frustrating for us due to the wet environment, however, it is often a reliable and low maintenance fire building method convenient for when you have additional tasks and chores to do, or you wish to keep your fire burning overnight while you sleep.

 

 

How to Clean a Fish in Three Steps

 

A few months ago when I went camping and fishing at Dick’s Creek with my friends, a friend of mine showed me this extremely simple way to clean a fish (in this case, a trout) without fileting. It’s great for a serving the fish in a way you can eat the meat off the bone. You can’t quite make a sandwich with this method, but it’s a very simple, very tidy way to do it. Here are the step by step instructions with pictures from my trip to Nimblewill Creek. It takes no more than 2-5 minutes per trout depending how good you are with your knife.

Tools You Need: A sharp knife, a source of water for rinsing, something to contain the cleaned fish, and a place to dispose or discard the parts you will not use.

Personally, I used my Khukuri knife and Dan his Rogue Survival Knife.

We just did this all by the creek for washing and discarding, and had a pan for the usable parts.

Step 1: Remove the Head

20170617_183934

Find a hard surface like a rock, and simply cut the fish through right behind the gills. Be careful of your fingers because a fish like a trout can be very slippery. You can keep the head if you wish to use it, or cook it that way, but I just discard it.

Update: It has been pointed out to me by RawSkillsBushcraft that a rock is not the ideal surface due to the potential for damaging your knife. Instead, find something like a piece of wood that will not dull your blade. Additionally, as I have done previously at Bongam Lake, you can absolutely keep the head to eat the meat from the cheeks or use in a soup. In a survival situation where every bit of protein matters, you need to do this.

 

Step 2: Cut Lengthwise from the Anus and Peel Open

20170617_184107

Make the cut beginning at the anus, and ending at the severed head deep enough that you can get your thumbs inside to peel the fish open cleanly, revealing two filets on the side, and a bunch of organs. Careful not to pop the gall or anything.

Update: For clarification, as a reader suggested, there are specific ways that eases this process. As tomcatHoly  explains, position the knife nearly parallel to the fish, angling it so the top quarter inch or so of the blade is pressing against the skin. Push forward to split open the thin membrane on the belly, which will split open as you go.

Now, alternatively, you can insert the knife point perpendicular to the fish at the anus, blade toward the “head” just enough so the knife penetrates through the  membrane: a quarter inch or so depending on the size of the fish. You need a sharp knife to do this method. At this point, just angle the knife with blade bent slightly toward the fish, and carefully cut the membrane in the direction of the “head.”

Step 3: Remove the Organs, Push out the Blood

20170617_184117

Pull the organs out carefully and discard. Last, press your thumb hard at the base of the spine and push out all the blood built up. Then just dunk the fish in water to wash it off, remove any extra blood or goo, and you’re done!

20170617_230634

Voila! Trout cleaned and ready to cook!

Thank you to the readers who provided suggestions to make this guide more detailed and easier to follow. I am open to any and all suggestions, critiques or anything else you wish to say either by comment or using the contact button at the top.

 

 

Twig Fires

20170430_143824

So we’ve decided to expand the blog to amateur bushcraft as well! We will be sharing as we learn new survival skills. The first skill we worked on today is building successful fires using twigs instead of split wood. It’s a quicker and easier method to get a fire going, and if done right, can be a sustained source of warmth, purification of water sources, and cooking. The smoke, as most know, also can keep away skeeters and chiggers and other annoyances. Here are the tools we used:

On the left, we have my gear. Sheffield Rogue survival knife, and “Light My Fire” Swedish fire steel. On the right are Dan’s tools– magnesium fire stick with compass, and bushcraft knife. Pink shoes optional. We decided to have a little competition as to who could get the quicker or better fire going.

There’s a couple things you need to accomplish this aside from those pictured above: materials for fuel, kindling, a foundation, and a brace.

20170430_135211

The key here is to gather a large amount of twigs in the beginning that could sustain the fire for hours or even days. So I set ahead to collect my resources, while Dan decided to go ahead and shave feathers off twigs to create kindling. As far as the material for fuel go, you want three different sizes (as I learned on Bushcraft USA): thumb width, pencil widith, and pencil lead width. We organized our twigs in generous handful sized piles. Another important note is do NOT gather twigs from the ground. Often dew, and rainwater can collect in the ground, saturating materials and making them difficult to light. Instead, we opted for dead hanging branches from the surrounding trees. You can tell its dead when the inside has no green, and it easily snaps off. I was slapped in the face, poked in the eye, wrapped in webs and chased by a couple spiders, but eventually gained some good sized piles.

20170430_135216

As you can see above, Dan eventually got his little piles together. For the foundation, as pictured above, Dan chose a small bed of stones which he will put his kindling on top of. This helps keep any coals that form inside your twig fire instead of falling to the ground which if wet or snowy will put them out.

For a brace, Dan put two larger paralleled logs against his foundation. This helps keep the materials together and will help build that conical shape that allows oxygen to flow freely through the fire and prevents your twigs from smothering the coals.  Dan’s setup was very cute and tiny. If it was in Korea, it would have had little googly eyes on it.

Here is my setup:

20170430_140946

I mean, we know who’s the true grisled woodsman here (or so I thought…). I chose two logs for a foundation, and two logs (one not pictured) for a brace. So for kindling, we shaved down twigs to create thin, curly shavings also known as feather sticks. Once we got about a fist full of that, it was time to begin attempting to light with our fire starters. We aimed the fire steel end down into the kindling, and flicked to create sparks which eventually will catch. Once it catches, we shield with our hands and blow until a small flame blooms. Then we grabbed a bunch of the pencil lead sized twigs and leaned them across the braces, following by pencil sized in a perpendicular pattern, then thumb sized, then repeat as needed.

20170430_140342

Dan was able to get his going really quick and definitely won out in terms of speed. His fire made it to waste high! The only issue was he definitely skimped on materials for fuel, and in a survival situation, more is better.

I on the other hand had some major issues getting my kindling to light. I assume the issue was my feather pile just wasn’t big enough, or the stick I used was slightly saturated. I must have knocked over my pile thirty times. Note to self, make sure the ground below your foundation is stable and not wobbly. What I ended up doing, after a lot of frustration, getting butthurt and proclaiming how annoying fire starting is, was grabbing a handful of dry grass from a nearby clearing and using that instead. The grass caught a lot easier, and I piled my fuels in the same pattern as mentioned before. Finally… the red flower came to me.

20170430_143854

I had gathered quite a bit of materials thought so was able to get it raging while i relished in success before putting it out. Word of advice, have some water to douse when you try this. Also make sure to move your equipment out of the way of the fire after its lit. Definitely melted the plastic handle of my fire steel…

This was overall a really easy and gratifying method for creating fire with only a few survival tools, and the natural materials around you. Definitely pocketing this one for future camping trips. Brook seemed to have fun with it, as well!

20170430_140221

I look forward to documenting more of our exploration of bushcraft in the future and honing these useful survival skills. Hopefully these posts can help others learn as well. One more piece on equipment– it doesn’t take the most expensive or brand names to be successful. The trick is to get a knife whose weight and size you can get comfortable with whether you be bushwhacking, shaving or cutting. As for the fire steel, longer ones are easier to use but its still about mastery of what you have.

I’m a big knife, little stick type of person. Dan’s a little knife, big stick type of person. Do what works for you. Or what you can withstand frustrating yourself over until you finally learn to use it right. I wonder if this says something about our personalities…